Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
equipment:sony:portable:mz-r3 [2022/12/26 16:44] – [Sony MZ-R3] jdub | equipment:sony:portable:mz-r3 [2024/01/01 05:20] (current) – inline edit specialk | ||
---|---|---|---|
Line 5: | Line 5: | ||
To get rechargeable AA's to work in an 'R3, you need press the rechargeable batteries switch. To do so, open up your MZ-R3, holding it so the bottom is facing up and the battery bay is on the far side. Pop the battery door open. On the right-hand side, you will see near the bottom a little pin. Get a bit of newspaper or eraser to hold the pin shut, then put your AA rechargeable batteries in. They should charge normally. Do this at your own risk; it isn't likely to be a Sony-approved technique. - // | To get rechargeable AA's to work in an 'R3, you need press the rechargeable batteries switch. To do so, open up your MZ-R3, holding it so the bottom is facing up and the battery bay is on the far side. Pop the battery door open. On the right-hand side, you will see near the bottom a little pin. Get a bit of newspaper or eraser to hold the pin shut, then put your AA rechargeable batteries in. They should charge normally. Do this at your own risk; it isn't likely to be a Sony-approved technique. - // | ||
- | -- Content adapted from [[http:// | + | -- Content adapted from [[http:// |
-------------------------------------------------------------------------------------------- | -------------------------------------------------------------------------------------------- | ||
Line 23: | Line 23: | ||
====== Manuals ====== | ====== Manuals ====== | ||
- | {{: | + | {{: |
- | {{: | + | {{: |
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
- | {{: | ||
====== Repair ====== | ====== Repair ====== | ||
- | [[https:// | + | [[https:// |
+ | [[https:// | ||
+ | |||
+ | Short circuit the soldering bridge of TAP801 (MODE) on the main board. (connect pin #46 to GND) and turn on the power. | ||
+ | When the test mode is set, the LCD will display the following: ver 00.09 00 | ||
+ | |||
+ | After the ROM version is displayed, there will be a pattern of all ON and all OFF. You can pause the display by pressing the PAUSE button. | ||
+ | |||
+ | There is also another (possibly the same?) test mode that can be accessed by: | ||
+ | Make sure the HOLD switch is ON | ||
+ | Connect a 24kohm resistor between pin 2 and 4 on the remote control input (pins are counted " | ||
====== Photos ====== | ====== Photos ====== | ||
Line 38: | Line 51: | ||
< | < | ||
< | < | ||
+ | < | ||
< | < | ||
< | < | ||
Line 44: | Line 58: | ||
</ | </ | ||
</ | </ | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
~~DISCUSSION~~ | ~~DISCUSSION~~ | ||
Line 55: | Line 74: | ||
equipment.mdlp | equipment.mdlp | ||
equipment.netmd | equipment.netmd | ||
- | equipment.web-md | + | equipment.web-md |
equipment.hi-md | equipment.hi-md | ||
equipment.radio | equipment.radio | ||
Line 61: | Line 80: | ||
equipment.weight | equipment.weight | ||
equipment.atrac-ver | equipment.atrac-ver | ||
+ | equipment.battery-page : BP-DM20, AA | ||
+ | equipment.battery-notes : | ||
+ | equipment.battery-num : | ||
equipment.battery | equipment.battery | ||
equipment.sidecar | equipment.sidecar | ||
Line 77: | Line 99: | ||
equipment.manual | equipment.manual | ||
equipment.region | equipment.region | ||
- | equipment.image | + | equipment.image |
equipment.status | equipment.status | ||
---- | ---- | ||